Operation precautions:
1) Reading the disk, if it is not smooth, you can turn off the power again and plug the USB socket.
7) The letter g is not pressed into place, and the active teeth (sinkers) hook up the yarn.
4) Check whether the eye sensor is damaged.
2) If there is too much difference between the left and right transfer positions of the needle transfer head of the same port, check whether the transfer triangle is standard in Dieshan.
5) Pay attention to rewinding cloth and sub-roller yarn (special attention to the national flower series)
3. The national flower series also has a pre-load.
3) Check whether the knitting needles are not smooth on the needle bed.
3) Adjust the size according to the proofing requirements.
7) See if the needle ruler is too tight or too loose.
(three) random flowers (random needle about Fully Computerized Flat Knitting Machine selection at https://www.fengfanjx.com/product/sweater-machine/fengfan-jinmingde-fully-computerized-flat-knitting-machine-type-a2-2.html)
1) Check whether the cloth squandering is regular, for example, which needle selector is the problem.
4) See if the needle selection stitch is too tight or too loose on the needle bed.Operation and maintenance method of domestic computerized flat knitting machine control system
1. Is it smooth?
5) Check the wiring, whether the plugs are properly inserted, and see if there is a bad connection.
2) Thread the yarn, and adjust the antenna elasticity and side antenna tension at the same time.
11) Whether the yarn feeder touches the hook or the needle tongue, and whether the yarn feeder screw is loose.
2) Two mouths do knitting at the same time, if one mouth is abnormal
If it becomes smaller, consider adjusting the origin of the degree to a larger value. Increase speed, pull, etc.
6) Check whether the main drive belt is too loose.40m/s, and release the row lock when the cloth reaches the main roller ( The Feihu machine clicks repeatedly).
8) Check whether the bottom plate of the head and the slider are in place and flexible. Adjust the gap between the needle selection jack and the needle bed.
3) The density is too loose
4) The pulling force is too small, and the antenna and side antennas have insufficient elasticity.
8) Replace the needle selection board.
(Seven) tuck yarn
1) Check whether the knitting needles are changed wrongly (for example, if 12 stitches are changed to 14 stitches)
2) Raise the needle plate without affecting the needle gap and the gap between the mouth.
2) Special circumstances can consider the problem of moving guides
3) The above two methods take into account the "needle transfer position"
(six) transfer stitch
1) Check if the needle transfer position is correct.
6) Check whether there is a mistake in the installation of the protection mountain.
2) Check whether the connecting pins run smoothly on the needle bed, and whether they bounce freely when pressed down by hand
3) Check whether the screw of the motor is loose.
5) See if the needle is damaged
(five) diagonal
1) If the oblique piece is after determining the tension of the cloth and the reason for the position of the wool yarn. Rally, etc.
6) When the degree of mesh is too tight, the loop cannot be released, and the connection pins will also be hit.
9) Is the degree stuck?
10) The abnormal sound of the yarn feeder is running, and the drum may not be locked. With the Huaxiang controller, you can switch the storage and reading media (U disk and disk) and then start to read the disk.
4) Determine the pattern expansion and the position of the yarn feeder. Start weaving
1) Check the cloth density and confirm the condition of coarse and young yarn at any time, so as to control the length of the garment at any time.
B, check whether the screw of the motor is loose.
2. Follow the foot model size. The national flower series depends on the swing of the electromagnet.
4) See if there is a problem left over from the previous line.
(two) hit the connection pin (the national flower series is called the long pin)
1) Check whether the degree is flexible.
(four) flat shake drop needle
1) See if it is caused by squandering
2) Check whether the sky pole is installed in a standard manner, which may cause the height of the yarn feeder to be aligned with the center seam of the mouth hole.
9) Re-find the origin, and pay attention to the copper head for the national flower series.
5) Hanging cloth (not used by the machine to lift the bottom plate), row lock (repeat for the flying tiger machine) immediately open and close the auxiliary roller, the head speed should be less than 0. How to deal with common problems
(一)
1) The mesh is getting bigger and bigger while weaving
A, check whether the wiring is poorly connected.
4) The shirt pieces are divided into yards, and the colors are neatly folded and packaged for delivery.
3) If the needle transfer position is correct, some of the needles are too high or too low, and the hole position is too different, and the needle plate needs to be trimmed to the standard.
5) Check whether the three pins of the pressing needle are in place.
7) Check whether the transfer needle guide block of the transfer triangle is smooth and flexible. To remove the piece of yarn, retry the mesh and tension.
3) Adjust the needle selection parameters, select the origin of the needle, and fine-tune the needle selection. (10) When knitting a tuck; instead of hanging the tuck, the tuck is knitted, and the needle triangle is not in place.
2) See if it was selected by stealth or missed.
2) Pay attention to the waxing of the wool yarn and the position of the wool yarn discharge.
.
5) Check whether Butterfly Mountain is an old type Butterfly Mountain. Whether the turntable is smooth. Lower the needle plate on the long side of the cloth and raise the needle plate on the short side.
3) Keep abreast of yarn usage, wool chromatic aberration, etc.
(eight) knitting needle
1) The needle is damaged and the needle tongue is not flexible
2) Mouth is too big
3) The density is too tight
(9) There is an abnormal noise when weaving
1) The main drive belt is too loose or too tight
2) Check if the head slider is crooked
3) Is the distance between the hill board and the needle board standard?
4) Whether the insert is flat
5) Is there any friction between the screws of the Xinke fixing plate and the Xinke seat?
6) Check whether the fixing screws of the head mount plate are loose,
7) Is the clearance between the bearing and the guide rail standard?
8) Whether the needle path of the knitting needle is smooth
1) Reading the disk, if it is not smooth, you can turn off the power again and plug the USB socket.
7) The letter g is not pressed into place, and the active teeth (sinkers) hook up the yarn.
4) Check whether the eye sensor is damaged.
2) If there is too much difference between the left and right transfer positions of the needle transfer head of the same port, check whether the transfer triangle is standard in Dieshan.
5) Pay attention to rewinding cloth and sub-roller yarn (special attention to the national flower series)
3. The national flower series also has a pre-load.
3) Check whether the knitting needles are not smooth on the needle bed.
3) Adjust the size according to the proofing requirements.
7) See if the needle ruler is too tight or too loose.
(three) random flowers (random needle about Fully Computerized Flat Knitting Machine selection at https://www.fengfanjx.com/product/sweater-machine/fengfan-jinmingde-fully-computerized-flat-knitting-machine-type-a2-2.html)
1) Check whether the cloth squandering is regular, for example, which needle selector is the problem.
4) See if the needle selection stitch is too tight or too loose on the needle bed.Operation and maintenance method of domestic computerized flat knitting machine control system
1. Is it smooth?
5) Check the wiring, whether the plugs are properly inserted, and see if there is a bad connection.
2) Thread the yarn, and adjust the antenna elasticity and side antenna tension at the same time.
11) Whether the yarn feeder touches the hook or the needle tongue, and whether the yarn feeder screw is loose.
2) Two mouths do knitting at the same time, if one mouth is abnormal
If it becomes smaller, consider adjusting the origin of the degree to a larger value. Increase speed, pull, etc.
6) Check whether the main drive belt is too loose.40m/s, and release the row lock when the cloth reaches the main roller ( The Feihu machine clicks repeatedly).
8) Check whether the bottom plate of the head and the slider are in place and flexible. Adjust the gap between the needle selection jack and the needle bed.
3) The density is too loose
4) The pulling force is too small, and the antenna and side antennas have insufficient elasticity.
8) Replace the needle selection board.
(Seven) tuck yarn
1) Check whether the knitting needles are changed wrongly (for example, if 12 stitches are changed to 14 stitches)
2) Raise the needle plate without affecting the needle gap and the gap between the mouth.
2) Special circumstances can consider the problem of moving guides
3) The above two methods take into account the "needle transfer position"
(six) transfer stitch
1) Check if the needle transfer position is correct.
6) Check whether there is a mistake in the installation of the protection mountain.
2) Check whether the connecting pins run smoothly on the needle bed, and whether they bounce freely when pressed down by hand
3) Check whether the screw of the motor is loose.
5) See if the needle is damaged
(five) diagonal
1) If the oblique piece is after determining the tension of the cloth and the reason for the position of the wool yarn. Rally, etc.
6) When the degree of mesh is too tight, the loop cannot be released, and the connection pins will also be hit.
9) Is the degree stuck?
10) The abnormal sound of the yarn feeder is running, and the drum may not be locked. With the Huaxiang controller, you can switch the storage and reading media (U disk and disk) and then start to read the disk.
4) Determine the pattern expansion and the position of the yarn feeder. Start weaving
1) Check the cloth density and confirm the condition of coarse and young yarn at any time, so as to control the length of the garment at any time.
B, check whether the screw of the motor is loose.
2. Follow the foot model size. The national flower series depends on the swing of the electromagnet.
4) See if there is a problem left over from the previous line.
(two) hit the connection pin (the national flower series is called the long pin)
1) Check whether the degree is flexible.
(four) flat shake drop needle
1) See if it is caused by squandering
2) Check whether the sky pole is installed in a standard manner, which may cause the height of the yarn feeder to be aligned with the center seam of the mouth hole.
9) Re-find the origin, and pay attention to the copper head for the national flower series.
5) Hanging cloth (not used by the machine to lift the bottom plate), row lock (repeat for the flying tiger machine) immediately open and close the auxiliary roller, the head speed should be less than 0. How to deal with common problems
(一)
1) The mesh is getting bigger and bigger while weaving
A, check whether the wiring is poorly connected.
4) The shirt pieces are divided into yards, and the colors are neatly folded and packaged for delivery.
3) If the needle transfer position is correct, some of the needles are too high or too low, and the hole position is too different, and the needle plate needs to be trimmed to the standard.
5) Check whether the three pins of the pressing needle are in place.
7) Check whether the transfer needle guide block of the transfer triangle is smooth and flexible. To remove the piece of yarn, retry the mesh and tension.
3) Adjust the needle selection parameters, select the origin of the needle, and fine-tune the needle selection. (10) When knitting a tuck; instead of hanging the tuck, the tuck is knitted, and the needle triangle is not in place.
2) See if it was selected by stealth or missed.
2) Pay attention to the waxing of the wool yarn and the position of the wool yarn discharge.
.
5) Check whether Butterfly Mountain is an old type Butterfly Mountain. Whether the turntable is smooth. Lower the needle plate on the long side of the cloth and raise the needle plate on the short side.
3) Keep abreast of yarn usage, wool chromatic aberration, etc.
(eight) knitting needle
1) The needle is damaged and the needle tongue is not flexible
2) Mouth is too big
3) The density is too tight
(9) There is an abnormal noise when weaving
1) The main drive belt is too loose or too tight
2) Check if the head slider is crooked
3) Is the distance between the hill board and the needle board standard?
4) Whether the insert is flat
5) Is there any friction between the screws of the Xinke fixing plate and the Xinke seat?
6) Check whether the fixing screws of the head mount plate are loose,
7) Is the clearance between the bearing and the guide rail standard?
8) Whether the needle path of the knitting needle is smooth
